How to Install Decorative Bollards with a Drop-In Insert
Drop-in insert installation is recommended for decorative applications to create architectural perimeters. This installation technique offers little impact resistance.
Drop-in anchors should only be installed in fully cured concrete that is at least 4" thick.1 All measurements in this installation guide assume a bare, level concrete surface.
What you will need
3/4" Drop-In Concrete Insert
3/4" Threaded Rod
3/4" Hex Nut
Hexagon Socket Set Screw
Plastic Polyethylene Plug
1" Masonry Drill Bit
3/4" Insert Setting Tool (or equivalent)
1" Socket Wrench
Hammer Drill or Rotary Hammer
3/16" Hex Key
To protect the finish, keep bollards in original packaging until the exact moment of installation
Handle with care to avoid scratching or damaging bollard surfaces as abrasions will lead to rust
Once scratched, bollards cannot be repaired to original form without re-finishing the entire surface
Check for hazards
Always check for hazards such as water pipes, gas lines, and underground wiring before drilling.
Clean the surface
Dirt and debris can affect the line of sight and disrupt placement of the bollards.
Use a broom or pressure washer to clean the concrete surface prior to bollard installation.
Study the site plans
Site plans are generally created by the architect of the project.
Refer to site plans to locate and mark the precise center point of each bollard.
For secure installation, ensure there is a minimum radius2 of solid concrete around each mark.
Drill the hole
Create pilot hole
Tap a pilot divot hole in the center of each mark.
This will prevent the hammer drill or rotary hammer from drifting while boring the hole.
Set the depth control on the hammer drill (or rotary hammer) to 3-1/8"
If depth control is not available, mark 3-1/8" on the masonry bit.
Drill the hole
Drill a hole that has a 1" diameter and 3-1/8" depth.
Drill on high speed, using the hammer function if available.
Check the masonry bit often to ensure it remains free of debris.
Secure the bollard
Clear the hole
Clear the hole of all debris and/or standing water using the vacuum.
Tap the drop-in insert into the hole
With the slotted end facing down, drive the drop-in insert (A) down until its top sits flush with the concrete surface.
Ensure that the top is perfectly level.
Set the concrete insert
Insert a setting tool (B) into the threaded hole, then hammer down.
If a proper setting tool is not available, an equivalent flat-end punch can be used.
This will cause the internal expansion plug to set the concrete insert in place.
Place the bollard base near the concrete insert
Keep the bollard in its protective packaging. Carefully place the bollard near the installation position.
When ready to install, remove its protective packaging.
Set the bollard over the concrete insert
Set the bollard base upright and maneuver it so the center lines up with the threaded hole in the concrete insert.
Lower the threaded rod and tighten
Lower the threaded rod through the bollard base.
Continue to thread the rod into the anchor casting.
Tighten3 the threaded rod by hand until it is secure in the concrete insert.
Secure the bollard
Place the washer over the threaded rod so that it rests on top of the bollard.
Apply the 3/4" hex nut to the threaded rod and tighten until the bollard is secure.
Secure the bollard cap
Remove bollard cap from its packaging.
Place the cap on the top of the shaft of the bollard.
Secure and align the cap to the bollard base with the three set screws. Tighten in equal amounts to ensure that the cap remains centered.
Place the plastic polyethylene plugs (C) over the set screw heads.
Inspect the installation
From a distance, examine the plane of view.
Ensure the bollard is plumb to the surface, and the surface is flat.
Check the bollard for any signs of surface damage
Abrasions should be covered as soon as possible to prevent rust and ensure the proper life of the bollard. For damage repair or other servicing needs, please contact Reliance Foundry’s sales department.
Care and maintenance
Reliance Foundry manufactures its products to the highest design standards to ensure their durability. Reliance’s bollards are finished with long-lasting Proper care and maintenance are required to maintain the finish and ensure a full service life.
1.Concrete insert manufacturers such as www.ucanfast.com recommend a concrete depth of at least 6"↩ 2.Concrete insert manufacturers such as www.ucanfast.com recommend a radius of 9"↩ 3.The manufacturer recommends tightening the threaded rod to a depth of approximately 1-1/2" into the concrete insert↩
Unit 207, 6450-148th Street
Surrey, British Columbia,